132 note: part numbers are shown for a single card of pre-printed tags numbered 1-50. 0105660000 0269120000 0105420000 0437920000 0105620000 8/65/52.5 (.31/2.56/2.07) 8/65/48.5 (.31/2.56/1.91) 12 (.47) 300 v / 25 a / #22...8 awg* 300 v / 25 a / #26...8 awg 380 vac / 27 a / 6 mm 2 1.7 (16) 3.5 t ype part no. ap (1.5) 0146760000 ap (3.0) 0146720000 tw (1.5) 0242960000 tw (3.0) 0242920000 tw (0.5) 0474700000 tsch 2 0353660000 ql 2 0194300000 ql 3 0194400000 ql 4 0194500000 ql 10 0338300000 vh 12 0249000000 bs m 3 x 20 cu 0377100000 qs 2 0270960000 qvs 2 0307300000 qvs 3 0329300000 qvs 4 0307400000 vh 19 0318000000 bs 25 bare 0334700000 qb 2 0205700000 qb 3 0205800000 qb 4 0205900000 qb 10 0343800000 ps 4 0299600000 ssp 3 0531760000 dek 5/6 0468660001 dek 5/6 0468760001 sakt 1/lt slide link disconnect terminals ql fixed final number indicates number of poles. see the accessories section for more information. sakt 2/lt 0445420000 0437720000 0106020000 0330620000 0105920000 8/82/52.5 (.31/3.23/2.07) 8/82/48.5 (.31/3.23/1.91) 12 (.47) 300 v / 25 a / #22...8 awg* 300 v / 25 a / #26...8 awg 380 vac / 27 a / 6 mm 2 1.7 (16) 3.5 t ype part no. ap (1.5) 0146760000 ap (1.5) 0329120000 tw (1.5) 0242960000 tw (2.5) 0351820000 tw (0.5) 0474700000 tsch 2 0353660000 ql 2 0194300000 ql 3 0194400000 ql 4 0194500000 ql 10 0338300000 vh 12 0249000000 bs m 3 x 20 cu 0377100000 qs 2 0270960000 qvs 2 0307300000 qvs 3 0329300000 qvs 4 0307400000 vh 19 0318000000 bs 25 bare 0334700000 qb 2 0205700000 qb 3 0205800000 qb 4 0205900000 qb 10 0343800000 ps 4 0299600000 ssp 3 0531760000 dek 5/6 0468660001 dek 5/6 0468760001 slide link see accessories section for additional information. *for ts 35 #22...8 awg **with ap 380 v slide link disconnect terminals offer a superior solution for simple current transformer circuits and measurement transformer test sets using sakt 1/lt lateral disconnect terminals, or sakt 1/du feed through terminals and sakt 1/qt cross disconnect terminals. current transformers must always have a closed secondary circuit, even when changing measuring equipment (see schematic below). stationary jumpers ql jumpers serve as fixed cross-connections for the disconnect terminals. the ql jumpers re quire the use of a fixing screw (bs m) and a connection sleeve (vh) when attaching the jumper to the current bar. the wqv jumpers are provided with a retained jumper screw. sliding jumpers qs and qvs jumpers are sliding jumpers. these jumpers are used to temporarily connect or disconnect adjacent terminal blocks. when the jumper screws are loose, the jumper can move to either open or close the cross connection between blocks. t ightening the jumper screws holds the jumper in either the open (disconnected) or closed (shorted) position. qb jumpers work in a similar manner except that the jumpers remain fixed. an internal sliding connection link connected to the current bar either opens or closes the connection based on whether the link is in contact with the jumper or not. ssp disconnect locks snap into the terminal block. these locks must be removed to change the position of the sliding link connection. qvs sliding qb l1 k l k l k ll1 l2l3 n 1 2 3 4 5 678910 l2 l3 n t erminal block selection data a vailable options version pa 2 stb test points pa back wall closed krg back wall open krg 4 stb 14 test points ?.0 krg 60 v** 1 stb 8.5 test point ?.0 krg 1 stb 8.5 test point ?.3 krg 2 stb 14 test points ? krg 2 stb 14 test points ?.3 krg dimensions wi dth / length / height mm (in.) for ts 32 for ts 35 insulation stripping length mm (in.) t echnical data rated voltage / rated current / wire size ul csa vde to r que nm (lb. in.) clamping screw m selected accessory data end plate (thickness mm) pa krg partition (thickness mm) pa krg hp small partition jumpers connection sleeve fixing screw connection sleeve fixing screw switchable jumper links t est plugs disconnect lock marking tags print consecutive horizontal consecutive vertical
|
